All guides

Solar Monitoring Systems Explained: What the Enphase, Tesla, SolarEdge, and FranklinWH Apps Show, and What to Do When Monitoring Stops

A residential solar monitoring system streams per-panel or whole-system data to your phone in near-real time — the three numbers to check every month are production, consumption, and export.

By Taylor Crouse — Founder, Helios Energy GlobalPublished

Quick answer

  • A solar monitoring system streams production, consumption, and export data from your inverter or gateway to an app — updates arrive every 5–15 minutes in most platforms.
  • The four most common platforms in Southern California each use a dedicated app: Enphase App (IQ Gateway), Tesla app (Powerwall 3 / Tesla solar), mySolarEdge (SolarEdge inverter), and FranklinWH App (aGate).
  • Check three numbers every month: production vs. the same month last year, whole-home consumption, and grid export.
  • When monitoring stops, work through this order: check your home Wi-Fi, power-cycle the gateway, reconnect in the app — only call for service if the inverter LED shows red or production is zero for more than one full sunny day.
Solar Monitoring Systems Explained: What the Enphase, Tesla, SolarEdge, and FranklinWH Apps Show, and What to Do When Monitoring Stops

A residential solar monitoring system is a gateway or communications device — installed alongside your inverter — that collects per-panel or whole-system data and streams it to a cloud platform you read through a smartphone app, typically refreshing every 5 to 15 minutes. The three numbers that matter most each month are total production (compare it to the same month last year using your app's history view), whole-home consumption, and net grid export — all three together tell you whether your system is earning its keep under today's California rates.

Last verified: November 2026 by Helios Energy Global.


What each platform monitors and which app it uses

Enphase — Enphase App + IQ Gateway

For a 2026 setup, the critical distinction is this: microinverters report to an IQ Gateway or compatible Envoy, not directly to your phone.

Enphase microinverters report to a compatible gateway, which sends monitoring data to Enphase's service; the homeowner app displays the data assigned to your account.

The homeowner-facing tool is the Enphase App (iOS and Android), separate from the installer-only Enphase Installer App. The Enphase App sends homeowner notifications when there is a grid outage and the battery SoC is below 50%, 30%, or a very low SoC.

If the Enphase App does not detect an active internet connection, it will attempt to connect directly to the IQ Gateway to allow you to continue monitoring your system.

What you see in the app: real-time production per microinverter, whole-home consumption (when consumption CTs are installed), battery state of charge for any Enphase IQ Battery, and a historical graph going back to day one. The app also enables real-time alerts about grid outages.

Tesla — Tesla App + Powerwall 3 / Tesla Solar

Once installed, customers can manage their system using the Tesla App. The customer interface is the Tesla Mobile App.

Through the Tesla app, owners can monitor solar production (since Powerwall 3 has a built-in solar inverter, it shows solar generation data directly), battery charge level, home consumption, and grid import/export — all in a real-time flow diagram.

The Tesla app shows whole-system production and consumption but does not provide panel-level data. If you have a Powerwall 3 with its integrated string inverter, you see total solar production without per-panel detail.

Historical data is available in daily, weekly, monthly, and annual views.

The app sends push notifications for grid outages, Powerwall activating backup mode, and system faults.

The Impact view sums it all up: how self-powered your home was over a month, how your energy split between solar, Powerwall, and the grid, and an estimate of the energy value your system produced.

Learn more about the Tesla Powerwall installer process and what to expect at commissioning, or see Tesla solar customer service and repair in California if you need support after installation.

SolarEdge — mySolarEdge App + SolarEdge Inverter

The mySolarEdge app is SolarEdge's official homeowner monitoring tool, available free on iOS and Android.

SolarEdge's mySolarEdge platform pairs with SolarEdge inverters and S-series power optimizers. The monitoring interface shows panel-level data including voltage, current, and power at each optimizer location.

SolarEdge also provides a module-level alert system that emails or pushes notifications when any optimizer reports a fault code. mySolarEdge also integrates with SolarEdge's Home Hub inverter for battery management, allowing users to set charge and discharge schedules through the app.

One practical note: the mySolarEdge app does not support push notifications as of 2026, so enable email alerts in the web portal to catch issues proactively. In the mySolarEdge app, begin by checking "Last Updated." Since SolarEdge data typically refreshes about every 15 minutes, this helps confirm you are viewing the most current information available.

For warranty details, see SolarEdge inverter warranty and replacement in California.

FranklinWH — FranklinWH App + aGate

The FranklinWH system consists of three essential parts: aGate, aPower, and the FranklinWH App. The aGate serves as the intelligent energy management center, controlling the entire system. Customers can remotely monitor their home energy status and control the FranklinWH system via the app.

Per FranklinWH's support documentation, the app is an intelligent assistant with the following features: data visualization charts of real-time and historic loads and energy conditions; electricity plan customization to match household needs; real-time notification for intelligent recognition of events; remote control of energy management anytime and anywhere; and prediction of available backup time based on battery state of charge and household consumption.

During normal grid-connected operation, the aGate tracks which circuits consume the most energy and when, helping you identify energy waste without needing a separate home energy monitor. The FranklinWH app presents this data in clean, intuitive charts showing consumption by circuit throughout the day.

The aGate has built-in communications (Ethernet, Wi-Fi, and even 4G cellular) to ensure it stays connected for monitoring and for receiving firmware updates.

Learn more about the FranklinWH aPower 2 system and how the aGate integrates with your existing solar.


Platform quick-reference table

Platform Hardware gateway Homeowner app Panel-level data Consumption monitoring Battery SoC
Enphase IQ Gateway Enphase App ✅ Per microinverter ✅ With CTs installed ✅ IQ Battery
Tesla Tesla Gateway / Powerwall 3 Tesla app ❌ System total only ✅ Built-in ✅ Powerwall 3
SolarEdge SolarEdge inverter (built-in) mySolarEdge ✅ Per optimizer ✅ With CTs installed ✅ If battery fitted
FranklinWH aGate FranklinWH App ❌ System total ✅ Per circuit (aGate) ✅ aPower 2

"With CTs installed" means consumption current transformers were wired at commissioning — confirm with your installer if you are unsure.


What the status colors and fault messages mean

Enphase IQ Gateway LEDs

Per Enphase's support documentation (published July 2026):

The network communications LED shows: solid green = connected to the Enphase Cloud; flashing green = connecting to Enphase Cloud or Wi-Fi router; off = no network available. When amber/red, verify the Wi-Fi and router connections, restart the router, and then reconnect the gateway to Wi-Fi using the Enphase App.

A power production LED showing amber/red means: check the Enphase App to identify the issue and contact the installer or Enphase Support if it persists. If it occurs during the day, check the breakers or review the system status in the Enphase App.

A device communication LED showing solid amber/red means: check the Enphase App to identify affected devices and restore connectivity, or contact the installer or Enphase Support if needed.

Enphase IQ Series Microinverter LEDs

Per Enphase's support article published September 2026: Enphase IQ Series Microinverters use a built-in status LED to indicate operating status, grid conditions, and fault states. Correct interpretation of these LED indications helps installers and system owners diagnose issues quickly.

Per Enphase's installer monitoring documentation: Green = everything is working as expected. Red = indicates an AC issue (check the wiring). Orange = the device is operating, but there may be a communication issue or it hasn't been fully provisioned yet.

A solid red status LED after DC power has been cycled indicates that the microinverter has detected a DC Resistance Low – Power Off event — this requires a service call.

Enphase IQ Battery LEDs

Per Enphase's support documentation (published June 2026): Solid blue = not charging or discharging, battery level below 25%. Solid greenish-blue = idle, battery level between 25% and 75%. Solid green = idle, battery level above 75%.

Soft pulse blue = discharging. Soft pulse green = charging.

Flashing red in a sequence of two = the IQ Battery is in an error state, which may require on-site inspection.

SolarEdge inverter LEDs

Per SolarEdge's homeowner mySolarEdge page: Green LED = the inverter is working correctly. Blue LED = the inverter is connected to the internet. Red LED = there is an error.

If no data appears on the app, it may be that the inverter is not connected to the internet (blue LED off) due to an internet provider switch, a changed Wi-Fi password, or a recent blackout. On mySolarEdge you can restore the inverter's internet connection by scanning the QR code on the inverter.

In the app itself: on an inverter with a screen, the status screen shows Pac[W] (the AC power being produced right now) and S_OK when the inverter is connected to the monitoring server.


Why monitoring stops — and the fix order

Most monitoring outages are connectivity problems, not hardware failures. Work through this sequence before calling anyone:

1. Check your home internet. SolarEdge's homeowner page names the causes it sees for a lost connection: an internet provider switch, a changed Wi-Fi password, or a recent blackout, and it says the connection can be restored from the app by scanning the QR code on the inverter. The same three causes apply to every platform.

2. Power-cycle the gateway. Unplug it (or flip its breaker) for 30 seconds and restore power. Wait five minutes for the device to reconnect.

3. Reconnect Wi-Fi in the app. In the mySolarEdge app, open the menu, choose Inverter Communication, tap Configure Wi-Fi at the bottom of the screen, pick your network and enter the password. Then look for the blue LED and for S_OK under the app's Communications or Status screens. On Enphase, the Enphase App guides you through the same reconnection flow.

4. Check for a firmware update in progress. A flashing amber Enphase gateway LED means a firmware update is in progress — do not unplug; wait up to 30 minutes for the update to complete. FranklinWH's aGate handles firmware updates over-the-air automatically.

5. Check the inverter LED directly. The SolarEdge inverter operates completely independently of the mySolarEdge monitoring portal. The same is true for Enphase microinverters — they keep producing even when the gateway is offline. A red inverter LED (any platform) with zero daytime production is the signal to call for service.

6. Rule out a dead inverter. Zero production on a clear day, combined with a red or off LED, points to an inverter or microinverter failure rather than a connectivity issue. See solar panels not working — what to check before booking a service call; that guide walks through the pre-call checklist so you arrive at the conversation with the right information.

Other causes of a monitoring gap

  • An installer account that closed. If the company that set up your system has gone out of business, your site may still be registered under their master account. See the section below on regaining access.
  • Cellular gateway with expired SIM. Some older gateways used cellular as a backup or primary path. If your gateway has no Wi-Fi and monitoring went dark, the cellular plan may have lapsed — contact the manufacturer's support line.
  • A failed gateway (not the inverter). The gateway is a separate piece of hardware. If power-cycling does nothing and the LEDs stay off or red, the gateway itself may need replacement. Your inverter and panels are almost certainly still producing.

Why your monitoring app and your utility bill never match exactly

This is one of the most common questions we hear. The short answer: they are measuring different things at different points in the circuit.

Your solar monitoring app shows total system production. Your utility bill only tracks electricity you pull from the grid and electricity you send to the grid. Your utility cannot see the solar energy you used directly in your home before it ever reaches the meter.

If your panels are producing 3 kW and your dryer is using 3 kW, that energy never crosses the meter. Your monitoring app can show it, but your utility meter usually doesn't count it because it never went to the grid.

There is also a measurement tolerance gap. Per analysis of SCE meter data, expect your inverter monitoring to show 2 to 5 percent more production than your utility meter records. The True-Up calculation uses the utility meter data, not the inverter data, so use your monthly net metering statements as the authoritative source for billing purposes.

Finally, billing cycles add another layer: when you open your solar app and look at your monthly production, the app defaults to standard calendar months. However, utility companies rarely read your meter on the first and last day of the month. If you are trying to compare your solar app vs electric bill to see if things line up, looking at a calendar month in your app won't work — you have to use the custom date filters in your solar monitoring app to perfectly match the specific billing cycle dates listed on your utility statement.

SCE vs. LADWP note: SCE customers on NEM 3.0 (the Net Billing Tariff) see export credited at avoided-cost rates that vary by hour — your app's export kWh total and your bill credit will diverge more than they did under NEM 2.0, because the rate applied to each exported kWh changes throughout the day. LADWP customers still receive retail-rate net metering, so their export kWh and bill credits track more closely. For a full explanation of how your annual True-Up is calculated, see solar true-up bill explained for California. If your bill is higher than expected despite good production numbers, why is my electric bill so high with solar panels covers the consumption-side reasons.


How to regain access when your original installer has closed

This is more common than it should be. Each manufacturer has a path for homeowners to claim direct ownership of their monitoring account.

Enphase: Enphase has issued firmware updates that restore access for homeowners via the Enphase App when the IQ Gateway had stopped reporting to the Enphase Cloud. If your installer's account is the only one tied to your system, contact Enphase homeowner support directly at enphase.com/contact/support with your system serial number (printed on the IQ Gateway). Enphase can transfer site ownership to a new homeowner account without requiring the original installer.

Tesla: Contact Tesla Energy support through the Tesla app (Account → Support) or at tesla.com/support. Provide your Gateway serial number and proof of property ownership. Tesla can migrate the site to a new owner account.

SolarEdge: You can claim a system locked to an installer's account or restore access after the portal went dark through the mySolarEdge setup process.

SolarEdge runs the monitoring platform, but installers create each site and invite the homeowner — SolarEdge support does not create homeowner accounts directly, so you will need to contact SolarEdge support (monitoring.solaredge.com) with your inverter serial number and a utility bill showing your address to initiate a site transfer.

FranklinWH: The hidden center of FranklinWH intelligence is a cloud platform. Data is constantly uploaded from the aGate to the cloud and is then available for analysis and control via the FranklinWH App. If your installer account has closed, contact FranklinWH support at franklinwh.com/support with your aGate serial number to initiate an ownership transfer.

In all cases, have your system's serial number ready — it is printed on a label on the gateway or inverter. If you need a technician to physically reconnect or recommission hardware after an account transfer, solar panel repair and maintenance is the right starting point.


When a monitoring gap means a service call

Not every dark dashboard is an emergency. Here is when to stop troubleshooting yourself and book a technician:

  • Zero production for more than one full sunny day after you have confirmed Wi-Fi is working and the gateway has been power-cycled.
  • A red inverter LED that does not clear after a power cycle — this points to a hardware fault inside the inverter or microinverter.

Enphase IQ Battery flashing red in a sequence of two — the battery is in an error state that may require on-site inspection.

  • One panel dark in the array view for more than two consecutive days — a single microinverter may have failed.
  • Production consistently 20% or more below the same month last year with no obvious weather explanation — this suggests a string or microinverter has quietly failed. See how much power does a solar panel produce in Southern California for expected output benchmarks by month and ZIP code.
  • Monitoring gap longer than 7 days even after reconnecting Wi-Fi — the gateway hardware may need replacement.

For Enphase-specific warranty coverage on microinverters and IQ Batteries, see Enphase warranty — microinverters and IQ Battery in California. For SolarEdge inverter replacement timelines, see SolarEdge inverter warranty and replacement in California.


Frequently asked questions about solar monitoring systems

What is a solar monitoring system and do I need one?

A solar monitoring system is the gateway hardware and app that reads data from your inverter or microinverters and displays production, consumption, and export in near-real time. You do not need it for your panels to produce power — but without it, a failed microinverter or inverter can go undetected for months, quietly costing you kilowatt-hours. Every system Helios installs includes monitoring commissioning as part of the job.

Which app should I download for my solar system?

Your app is determined by your inverter and battery hardware, not by personal preference. Enphase systems use the Enphase App; Tesla Powerwall 3 or Tesla solar systems use the Tesla app; SolarEdge inverters use mySolarEdge; FranklinWH aPower 2 systems use the FranklinWH App. Your monitoring app is determined by your inverter and battery choice, not selected independently. If you choose Tesla Powerwall 3, you get the Tesla app.

Why does my Enphase app show less production than I expected?

If the meter (blue) production is significantly higher than the microinverter (grey) production, this suggests some devices aren't communicating properly. Open the array view and look for any grey or orange panels — those are the units not reporting. If more than one or two are grey on a clear day, call your installer. For expected output benchmarks, see how much power does a solar panel produce in Southern California.

Why does my monitoring app show more kWh than my SCE or LADWP bill credits?

Your solar monitoring system and your utility meter are measuring completely different things. SCE, PG&E, and other California utilities only track net grid transactions — the electricity that flows to and from the grid through your meter. When you produce 500 kWh of solar energy in a month but consume 400 kWh during daylight hours, your utility meter only registers the excess 100 kWh you exported to the grid. Self-consumed solar never touches the meter.

Does NEM 3.0 change what I should watch in my monitoring app?

Yes. Under NEM 3.0, which applies to all new solar installations in California since April 2023 on investor-owned utilities, the production number alone tells you almost nothing useful about your utility bill.

With both production and consumption streams active, your monitoring app can display the overlap between them: the amount of solar power being consumed directly in real time. This is the self-consumption metric that NEM 3.0 makes financially critical. LADWP customers are not on NEM 3.0 and still receive retail-rate net metering — see NEM 3.0 explained for a full breakdown of which utilities are affected.

Can I monitor my solar system without internet?

If the Enphase App does not detect an active internet connection, it will attempt to connect directly to the IQ Gateway to allow you to continue monitoring your system. SolarEdge offers a Bluetooth-based local app called SolarEdge Go for real-time data when the portal is offline. The FranklinWH aGate has built-in communications including 4G cellular as a fallback so it can continue reporting even if your home Wi-Fi goes down. The Tesla app requires an internet connection to the Tesla cloud.

What should I do if my installer has gone out of business and I can't see my monitoring data?

Contact the manufacturer's homeowner support line directly with your gateway or inverter serial number and proof of address. Enphase, Tesla, SolarEdge, and FranklinWH all have ownership-transfer processes that do not require the original installer. If the gateway hardware itself needs to be recommissioned, book a service visit through solar panel repair and maintenance — any certified installer for that platform can take over the account.


Next steps

Get a free consultation and custom design.

No pressure, no obligation — the owner reviews every design we send.